Jasco products universal remote control instruction manual 9 pages. Jasco products universal remote control instruction manual 16 pages. Jasco products company universal remote instruction manual 30 pages.
Jasco products company universal remote instruction manual 34 pages. Jasco products universal remote control instruction manual 37 pages. Jasco products universal remote control instruction manual 11 pages. Jasco products company universal remote instruction manual 9 pages. Jasco products company universal remote control instruction manual 36 pages. Jasco products company universal remote control instruction manual 25 pages.
You it gives you total control—at the touch of your Page 4: Menu Operation red indicator will turn off. To test the feature put the remote in another mode such as the TV mode if you programmed the audio receiver to be the Master Volume Device. If the audio receiver volume changes then the remote is programmed correctly.
If the TV volume changes and not the audio receiver, you will have to repeat the steps above and test again. Press and hold the SETUP button until the red indicator stays on approximately 4 seconds and then release the button. Press and release the MUTE button. The red indicator light will blink twice and go off. Press and release the 1 button. Count the number of times the remote light flashes. This is the number corresponding to the first digit of the code.
Repeat the process by pressing the 2, 3 and 4 buttons for the remaining digits. Press and release the number 0 button. The red indicator light will flash twice. You might have to reprogram your remote after installing new batteries. Try programing remote with a new code. Jasco Products Company warrants this product to be free from manufacturing defects for a period of ninety days from the original date of consumer purchase.
This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this unit. This warranty is in lieu of all other warranties express or implied. Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damages, so the above limitations may not apply to you.
This warranty gives you specific rights, and you may also have other rights which vary from state to state. If unit should prove defective within the warranty period, return prepaid with dated proof of purchase to:.
Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. To Install the Batteries 1. Battery Saver Your remote automatically turns off if the buttons are depressed more than 8 seconds. Code Saver You will have up to 10 minutes to change the batteries in your remote without losing codes you have programmed.
Selects device to control. DOT: Used to select digital channels, e. Button Functions, cont. TV sound while the picture remains. OK Selects menu items for the device you are controlling. Direct Code Entry Recommended 1. If the code entered is a valid code, the red indicator light will turn off. If the code entered is not a valid code, the red indicator light will flash and remain on allowing you to re-enter the code.
Press and hold the SETUP button until the red indicator light stays on approximately 4 seconds and then release the button. If it does not, return to step 2 and start the auto search again.
Make sure to hookup and power on all the devices you want to setup. Note down the GE universal remote codes from the list provided. Nothing is more frustrating to find out that you have not hooked up or universal remote batteries are bad after spending your evening on programming GE remote. Flip your remote, Open battery cover remote batteries, you will see a sticker showing the Mode and code list version.
The red light will remain on. Press and release the device button on the remote for the type of device you wish to control. The red light will blink once and remain on. NOTE: If there is not a device button on the remote for your type of device, you can use any device button on the remote.
Use the number buttons on the remote to enter the first code shown here. The red light will turn off after entering the fourth digit. Point the remote at the device. Test the buttons on the remote to see if the device responds as you would expect. If the buttons do not operate the device, return to Step 1 above and use the next code in the list.
0コメント